PVC異型材生產線

設備特點：

PVC異型材生產線主要用于PVC門窗型材、寬幅門板、窗臺板、多孔穿線管(四孔、六孔、七孔、九孔等)擠出。該生產線可以根據不同型材 斷面及模具，選用不同規格的平行(錐形)雙螺桿擠出機，并配置相應的真空定型臺，牽引機，切割機，翻料平臺等輔助設備。

主機擠出量可以在每小時60公斤到700公斤之間任選。 牽引機采用我公司獨 特升降技術，工作平穩，可靠性好，牽引力大。真空定型采用特殊加大渦流冷卻系統，便于冷卻定型，以滿足高速擠出的需要。切割機移動速度與牽引速度保持同步，全部動作采 用進口PLC電腦控制，設計合理，運行穩定，可自動定長切割，并配備粉塵回收裝置。根據不同的模具，定型臺可選用4米、6米 、8米、11米等規格。配置平行雙螺桿擠出機，特別適用于型材高速擠出。

主要技術參數：

大板材寬度(mm): 180, 240, 300, 600,900, 1200

牽引高度(mm): 150, 150, 150, 150, 150, 150

牽引力(KN): 2, 2, 2, 30, 40, 50,

牽引速度(m/s): 0-5, 0-5, 0-5, 0-3, 0-2.5, 0-2.5

輔機總功率(k w): 35, 35, 30, 30, 40, 45

冷卻水容量(m3/h): 6, 6, 6, 9, 12, 15

壓縮空氣壓力（M pa): 0.6, 0.6, 0.6, 0.6, 0.6, 0.6

PVC Profiled Material Production Line

Characteristics of the equipment 

HM Series PVC non-profiled material production line is mainly used in PVC door & window profiled material, wide door plate, window plate, extrusion of multi-holes pipe for passing through lines (four holes, six holes, seven holes, nine holes, etc.) For different sectional surface and molds, twin parallel (conical) screws extruder of different specifications can be chosen together with corresponding vacuum calibrating table, haul-off unit, cutting unit, tilter, etc. Capacity of main frame can be optionally chosen from 60-700kgs/hour. The haul-off unit has applied unique lift technique of our co. Its work is stable, its reliability is good, its pulling force is large. Vacuum setting has applied special enlarged vortex cooling system which is good for cooling and calibrating so as to meet demand of high speed extruding. Movement speed and drawing speed of cutting machine keep synchronous. All movements are controlled by imported PLC, the design is reasonable, the operation is stable, it can conduct automatic cutting with fixed length. Powder & dust suction device can be provided. With different molds, the tilter platform can choose such specifications as 4-meter, 6-meter, 8-meter, 11-meter, etc. With twin parallel screws extruder, it is particularly suitable for high speed extruding of profiled material. 

The main technical parameters:

Max. width of board (mm): 180, 240, 300, 600, 900, 1200

Drawing height (mm): 150, 150, 150, 150, 150, 150

Drawing force (KN): 2, 2, 2, 30, 40, 50

Drawing speed (m/s): 0-5, 0-5, 0-5, 0-3, 0-2.5, 0-2.5

Auxiliary equipment sum power (k w): 35, 35, 30, 30, 40, 45

Cooling water consume (m3/h): 6, 6, 6, 9, 12, 15

Compression air (M pa): 0.6, 0.6, 0.6, 0.6, 0.6, 0.6